Copper activated LiF nanorods as TLD material for high exposures of gamma-rays

Lithium fluoride (LiF) doped with proper activators is a highly sensitive phosphor commonly used for radiation dosimetry using thermoluminescence (TL) technique. Nanorods of this material activated with Cu, Mg and P as single dopants are synthesized in our laboratory and exposed to gamma-rays for their thermoluminescence (TL) properties. The induced TL glow curves of the Cu, Mg and P doped samples are similar with a single peak at 410 K. Copper doped sample is found to be the most sensitive sample with TL intensity around 65, 7 and 8 times of those of LiF:Mg, LiF:P and LiF:Mg,Cu,P, respectively, indicating that Cu is the luminescence center in the host of LiF nanorods, while Mg and P act as TL quencher particularly when used as codopants. These observations on the nanostructured form of LiF doped with these activators are entirely different from those of the widely studied LiF:Mg,Cu,P and LiF:Mg,Ti single crystals. The nanorods of LiF:Cu might be used for heavy doses measurement as they are sensitive to gamma-rays and have a linear TL response curve in a long span of exposures.     

Characterization of tribocharging properties of powder paint

The charge-to-mass ratio (q/m) of individual particles plays a vital role in the powder coating process. Simultaneous measurements of particle size and electrostatic charge were performed on triboelectrically charged powder paint and other powders in the particle size range 1.0 to 65.0 μm in diameter. An electrical single particle aerodynamic relaxation time (ESPART) analyzer was used to measure electrostatic charge (q) and aerodynamic size (d_a) distributions on a single particle basis and in a noninvasive manner. The powders were triboelectrically charged against nonconducting surfaces. Experimental data show that (1) the magnitude of the charge increases linearly with the surface area of the particle and consequently, the charge-to-mass ratio of the particles decreases inversely with respect to d_a in the entire size range, and (2) twenty to sixty percent of the particles were charged with opposite polarity. The average charge attained by particles larger than 4.0 μm in diameter was less than the Gaussian limit of saturation charge. The charge-to-mass ratio of the bulk powder sample depends upon the range of particle size in the sample. The mass median aerodynamic diameter of the sample studied was 30.0 μm with the geometric standard deviation of 2.0     

A scalable manufacturing process for flexible active‐matrix e‐paper displays

Abstract— A scalable manufacturing process for fabricating active‐matrix backplanes on low‐cost flexible substrates, a key enabler for electronic‐paper displays, is presented. This process is based on solution processing, ink‐jet printing, and laser patterning. A multilayer architecture is employed to enable high aperture ratio and array performance. These backplanes were combined with E Ink electrophoretic media to create high‐performance displays that have high contrast, are bistable, and can be flexed repeatedly to a radius of curvature of 5 mm.     

Circuit behavior modeling and compact testing performanceevaluation

A realistic modeling of circuit output error patterns with random test inputs is suggested. The model can be used as the basis for accurate evaluation of the probability of aliasing in compact testing. For several example compression techniques, the following aspects are investigated: identification of the error patterns that cause aliasing; asymptotic effectiveness analysis; and comparative simulation study with a limited number of random test vectors applied     

Studies on removal of metribuzin, bromacil, 2,4-D and atrazine from water by adsorption on high area carbon cloth

The removal of pesticides such as metribuzin, bromacil, 2,4-d and atrazine from aqueous solutions was studied by adsorption on high area carbon cloth. The adsorption process was followed by in situ UV-spectrophotometric technique in a specially designed adsorption cell. Spectroscopic data of the pesticides were determined in separate experiments. The extent of adsorption was quantified by calculating the amount of adsorbate adsorbed per unit area of the carbon cloth and the percentage coverage at the carbon-cloth surface. The order of extent of adsorption of the pesticides studied was found as metribuzin < 2,4-D < bromacil < atrazine. The adsorption process was found to follow a first-order kinetics and the rate constants were determined. The competitive adsorption of pesticides was also examined by carrying out the adsorption process from a solution of equimolar mixture of bromacil and metribuzin.     

An application of design space for assembly process reasoning to utilize current assembly plant resources for new product family members

A successful and profitable product platform strategy requires both product family architecture and assembly process reasoning. New product family member production cost and time can be significantly reduced by utilizing available assembly resources, which can be achieved through systematic assembly process reasoning. A method to utilize existing assembly plant resources, during the development of new product family members, requires comparing feasible assembly processes with exiting assembly plants. The set of feasible assembly sequences for a product family member is modelled by developing an assembly sequence design space, which is combinatorial in nature, and applying constraints on the space. Models that capture effects of constraints on these spaces, explicitly represent feasible regions, and efficiently enumerate designs within this space are investigated. The feasible space is then searched to determine new product assembly sequence that will require minimum change in the current assembly plant. An automotive front structure family is utilized to demonstrate application of the assembly sequence space to perform assembly reasoning to increase exiting assembly plant resource utilization.     

Product family design and platform-based product development: a state-of-the-art review

Product family design and platform-based product development has received much attention over the last decade. This paper provides a comprehensive review of the state-of-the-art research in this field. A decision framework is introduced to reveal a holistic view of product family design and platform-based product development, encompassing both front-end and back-end issues. The review is organized according to various topics in relation to product families, including fundamental issues and definitions, product portfolio and product family positioning, platform-based product family design, manufacturing and production, as well as supply chain management. Major challenges and future research directions are also discussed.     

Dopamine D? receptor stimulation of the nucleus accumbens or the medial preoptic area promotes the onset of maternal behavior in pregnancy-terminated rats.

There is good evidence that interference with the mesolimbic dopamine (DA) system results in impaired maternal responding in postpartum female rats. However, whether activation of the mesolimbic DA system is capable of promoting maternal behavior has not been investigated. This study examined whether increasing DA activity in various brain regions of pregnancy-terminated, naive female rats would stimulate the onset of maternal behavior. Experiments 1 and 2 examined the effects of microinjection of various doses (0, 0.2, or 0.5 μg/0.5 μl/side) of a D? DA receptor agonist, SKF 38393, or a D? DA receptor agonist, quinpirole, into the nucleus accumbens (NA) on latency to show full maternal behavior, and Experiment 3 determined the effects of SKF 38393 injection into a control site. Finally, because the medial preoptic area (MPOA) is also important for maternal behavior, receives DA input, and expresses DA receptors, the authors examined whether microinjection of SKF 38393 into MPOA was capable of stimulating the onset of maternal behavior. Results indicated that microinjection of SKF 38393 into either the NA or the MPOA facilitates maternal responding in pregnancy-terminated rats. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Thermal degradation and ageing behavior of microcomposites of natural rubber,carboxylated styrene butadiene rubber latices,and their blends

The effect of microfillers on the thermal stability of natural rubber (NR), carboxylated styrene butadiene rubber (XSBR) latices, and their 70/30 NR/XSBR blend were studied using thermogravimetric method. Microcomposites of XSBR and their blend were found to be thermally more stable than unfilled samples. The activation energy needed for the degradation of polymer chain was calculated from Coats‐Redfern plot. Activation energy needed for the thermal degradation of filled samples was higher than unfilled system. It indicated the improved thermal stability of the filled samples. The ageing resistance of the micro‐filled samples was evaluated from the mechanical properties of aged samples. The thermal ageing was carried out by keeping the samples in hot air oven for 7 days at 70°C. The mechanical properties such as tensile strength, modulus at 300% elongation, and strain at break were computed. As compared to unfilled samples, micron‐sized fillers reinforced systems exhibited higher ageing resistance. Finally, an investigation was made on the influence of ion‐beam irradiation on microcomposites of NR, XSBR latices, and their 70/30 blend systems using ²⁸Si⁸⁺ performed at 100 MeV. The surface changes of the samples after irradiation were analyzed using X‐ray photoelectron spectroscopy. The results of XPS measurements revealed that the host elements were redistributed without any change in binding energies of C_1s, O_1s, and Si_2p. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007